How to Replace a Tub Yourself: Removing and also Replacing.
How to Replace a Tub Yourself: Removing and also Replacing.
Blog Article
How do you really feel on the subject of How to Install a Bathtub?
Setting up a tub isn't exactly brain surgery, however it does require strong plumbing, carpentry, and occasionally, tiling skills. Replacing an old tub with a brand-new one is additionally a reasonably tough project. If the old bathtub is easily obtainable, the project can relocate quickly; if you need to open up a wall to eliminate the old tub and also position the brand-new tub, the job is much harder. In either instance, the project is within a house handyman's abilities, although you will require a helper to leave the old tub as well as embeded in the new one. Make sure you have actually certified yourself for the work and fit attempting it. Instead of hiring a service provider to take over a halfway-completed job, it is far better to think about using one before you start. Chances are you may need a specialist plumber to make tube connections.
This write-up will assist you mount a new bath tub in your washroom if you have already gotten a brand-new tub and don't require to transform the arrangement of your previous supply of water pipes.
Your devices and material list need to consist of the following:
Preparing for the Installment
To start with, the supporting frame supplied with the bathroom needs to be fitted (if required) according to the manufacturer's instructions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is very important to see to it that if the faucet features a plastic washing machine, it is fitted between the bath and the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the taps system to avoid stress on the tub.
Fit the versatile faucet ports to the bottom of the two taps using 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Ensure you use every one of the supplied washing machines.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath need to currently be ready to be suited its final placement.
Removing Old Taps
If you need to change old taps with new ones as a part of your installment, after that the first thing you need to do is detach the water. After doing so, activate the taps to drain any kind of water remaining in the system. The process of eliminating the existing faucets can be quite troublesome because of the limited access that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the faucets. Have a cloth prepared for the remaining water that will certainly come from the pipelines. When the supply pipes have actually been eliminated, utilize the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single taps from transforming throughout this process. Once the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing substance.
Prior to proceeding to fit the new faucets, compare the pipeline links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the new faucets to fit.
Installing the Bath tub
Utilizing the two wood boards under its feet, put the bathtub in the called for position. The wood boards are valuable in equally spreading the weight of the tub over the area of the boards as opposed to focusing all the weight onto 4 little points.
The following objective is to make sure that the bath tub is leveled all round. This can be accomplished by examining the spirit level and readjusting the feet on the tub until the level checks out level.
To set up taps, fit all-time low of the furthest adaptable tap connector to the proper supply pipeline by making a compression join; after that do the very same for the other faucet.
Activate the water system and examine all joints and brand-new pipework for leakages and tighten them if required. Fill up the bathtub and additionally check the overflow outlet and also the typical outlet for leakages.
Ultimately, take care of the bath paneling as explained in the manufacturer's user's manual. Tiling and also sealing around the bathtub must wait up until the bathtub has actually been utilized a minimum of once as this will resolve it right into its final position.
Suitable New Touches
If the tails of the new faucets are plastic, then you will require a plastic connector to avoid damage to the string. One end of the port fits on the plastic tail of the tap and the various other end offers a connection to the current supply pipes.
If you require to fit a monobloc, after that you will certainly need reducing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the mounting opening in the bath/basin guaranteeing that the washers remain in area between the faucet as well as the sink. Secure the faucet in place with the supplier offered backnut. Once the faucet is firmly in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with normal tap connectors. The previous type needs to be linked to the tap finishes first, tightening up just by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the location where the bath fulfills the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to crack a stiff seal, creating the water to pass through the wall surface between the bathroom and the tiling, causing complications with wetness as well as possible leakages to the ceiling below.
You can select from a range of coloured sealers to assimilate your fixtures as well as installations. They are sold in tubes and cartridges, as well as can securing gaps up to a width of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with twists of drenched paper or soft rope. Remember to always fill up the tub with water prior to securing, to allow for the motion experienced when the bathtub remains in use. The sealer can split rather early if you do not take into consideration this motion prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally easily offered on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water-proof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a devoted reader on Tools You Need to Install a New Bathtub , I think sharing that excerpt was a good idea. Loved our write up? Please share it. Let others locate it. Many thanks for going through it.
Find Out More Report this page